Shopping Cart

Page not found

BROWSE THOUSANDS OF LUMBER PRODUCTS

Individual Pieces
IMB1095_1

$22.37

IMB1095
1.44" x 2.94" x 35.5"

Cracks. Defect on edge.

PADAUK1488_1

$60.88

PADAUK1488
0.94" x 6.13" x 61.13"

Nice color.

WENG1398_1

$56.18

WENG1398
0.94" x 7" x 39.75"

Nice board.

CUM1067_1

$35.52

CUM1067
1.13" x 5.88" x 36.06"

Bark inclusion,Crack,Edge defect

PAUFER1167_1

$71.65

PAUFER1167
1" x 8" x 47.25"

Skip planed,Cracks,Edge defect

Pre-cut Sizes
BLAF1117_1

$19.99

BLAF1117
1.88" x 2.63" x 2.94"

Clear.

SIDEROSEEI0424_1

$45.00

SIDEROSEEI0424
0.2" x 4.38" x 32"

Clear.

BUBGS0284_1

$30.00

BUBGS0284
0.2" x 5.13" x 33.25"

Clear.

SIDEROSEEI0134_1

$45.00

SIDEROSEEI0134
0.2" x 4.5" x 31.81"

Bookmatched Guitar Sides set

Lumber Packs
birflr1.5X1_04

$244.00

PROJBIRCHFLR1001

20 BF Roasted Flame Birch project pack

Lengths: 60″-92″ (last piece might be shorter to balance BF total)
Widths: 4″ and wider
Thickness: Only 4/4 (nominal thickness) available

We S2S by default – surfaced thickness will be up to 1/4″ less than nominal thickness.
You can choose to get the lumber in the rough by selecting Machining = none and get an additional $20 off.

Note:
Lead time is 3 working days.
Ships free via UPS/USPS.

projmapbew1flf

$247.00

PROJMAPBEHLFW1F1001
1" x 4" x 48"

20 BF Low-Medium Figure Birdseye Maple W1F project pack

Figure: Low-Medium
Color: White 1 Face and Better
Lengths: 60″-92″ (last piece might be shorter to balance bd.ft total)
Widths: 4″ and wider
Thickness: 4/4 nominal

We S2S by default – surfaced thickness will be up to 1/4″ less than nominal thickness.
You can choose to get the lumber in the rough by selecting Machining = none and get an additional $20 off.

Note:
Lead time on rough lumber is 2 working days.
Lead time on S2S is 3 working days.
Ships free via UPS/USPS.

kiaat20bf

$320.00

PROJKIAAT1001
" x " x "

20 BF Kiaat project pack

Lengths: 60″-92″ (last piece might be shorter to balance BF total)
Widths: 4″ and wider
Thickness: Choose 4/4, 6/4 or 8/4 (nominal thickness)

We S2S by default – surfaced thickness will be up to 1/4″ less than nominal thickness.
You can choose to get the lumber in the rough by selecting Machining = none and get an additional $20 off.

Note:
Lead time is 3 working days.
Ships free via UPS/USPS.

GONCA_20bf

$280.00$290.00

PROJGONC1001
" x " x "

20 BF Goncalo Alves project pack

Striping: Variable – Typically Light to Medium
Lengths: 60″-92″ (last piece might be shorter to balance BF total)
Widths: 4″ and wider
Thickness: Choose 4/4 or 8/4 no minal

We S2S by default – surfaced thickness will be up to 1/4″ less than nominal thickness.
You can choose to get the lumber in the rough by selecting Machining = none and get $20 off.

Note:
Lead time is 3 working days.
Ships free via UPS/USPS.

On Sale!
IVRED1031_1

$596.95

IVRED1031
2.75" x 8" x 54.75"

Surface checks in sapwood. End checks and pith one side.

KINGB190

$1,700.00

KINGB190
6" x 7" x 62"

Stunning Kingwood Boule – sold as one
All pieces are from the same log, so book-matched.
Sold individually pieces would cost almost $1900.  Now on special for $1700

PIECELENWIDTHILBGRDNOTES
KINGB190A            60.75           5.50              1.00              5.4ANice Board.
KINGB190B            60.5           6.50              1.06              6.5A6″ crack on end.
KINGB190C            61.0           7.00              2.25            10.6CRustic.
KINGB190D            60.5           6.00              1.00              6.2ASmall crack on end.

 

IVRED1028_1

$276.10

IVRED1028
1.3" x 7" x 56"

Max width 8″. Min width 6.25″. Large defect one end. Good face has 2 small knots. Defects on reverse face

IVRED1029_1

$332.43

IVRED1029
1.3" x 7.5" x 56.25"

Max width 8″. Min width 7″. Hairline cracks on one face. Good face has minor end checks one end.

WOOD OF THE WEEK

15% off - this week only

Wenge
Wenge Lumber @ Rare Woods USA

Wenge is unique among the world’s exotic woods. This tough tropical wood’s distinctive deep chocolate color — which can sometimes augmented by muted gold, orange, red or even burgundy tint — is actually known as “Wenge” in the color spectrum nomenclature of various parts of the world (with paint manufacturers, etc.). Its grains are generally straight (though sometimes wavy or irregular) and are accenuated by overlapping black lines which typically decorate the board’s surface.

While being considered a strong, durable wood, Wenge’s course, rugged texture makes it very splintery — making some craftsmen hesitant to use it. It can be difficult to work, although is glues well and is considered a very dimensionally stable species.

Exercise caution when working with this wood. Its splinters can be like little razors and when one pentetrates the skin, it is quite painful and the area can quickly and easily get infected, if quick action isn’t taken to remove it (the splinter) and sterilize the area.

Although most sources consider Wenge to be a dull wood with poor natural luster, our experience has revealed that a deep, glossy luster can sometimes emerge through fine-grit sanding of flatsawn boards. Its combination of relatively light weight, rot & insect resistance and impressive tensil strength has yielded the wood to a variety of indoor and outdoor uses, being particularly well suited for flooring in heavy traffic areas.

Wenge Lumber @ Rare Woods USA
Main Color GroupDark Brown
Grain Pattern Pronounced
Avg Dry Weight - LB/BF4.5
Avg Dry Weight - KG/M3870
Janka Hardness - LBF1930
Janka Hardness - N8600
0
    0
    Your Cart
    Your cart is emptyReturn to Shop